CKI Cpl Porter Posted October 28, 2007 Share Posted October 28, 2007 I was just wondering if anyone could give me there 2 cents on my pbsv.cfg. I am new to steaming and not for sure what everything in here is for. I do know that I do not have the time to look over all kinds of SS nor the energy. If SS's are important to catching cheats then I guess I will have to make the time and energy. I do want to have a log of every player who joins my servers so that if at some point in time I need to look up a player's GUID or IP, I can. Pleae lend me your experience here and let me know what I should change. Thanks alot for the input. Also, I am streaming to Punksbusted too. ;Auto Generated by PunkBuster Server ; Some of the following settings may not apply, ; consult manuals at evenbalance.com for full documentation pb_sv_load pbsvuser.cfg pb_sv_banload pb_sv_MsgPrefix "PunkBuster Server" //[PB Message Prefix (default=^3PunkBuster Client)] pb_sv_MaxDlRate 4 //[KB/sec requested per file (default=4)] pb_sv_MaxConDls 1 //[Concurrent downloads (default=1)] pb_sv_KickLen 2 //[Minutes (default=2)] pb_sv_CvarFreq 6 //[# of range checks per minute] pb_sv_CvarLogging 1 //[1=Reg. Log, 2=Var Log, 3=Both, 0=Neither] pb_sv_CvarWalk 1 //[0=disabled, 1-4=Walk through obtained Cvar lists] pb_sv_CvarUserPulse 99 //[Frequency to auto-send CvarUser (minutes)] pb_sv_CvarChangedPulse 99 //[Frequency to auto-send CvarChanged (minutes)] pb_sv_CQC 1 //[0=No, 1=Yes (default=1)] pb_sv_LogSync 0 //[0=No, 1=Yes (default=0)] pb_sv_SsFloor 1 //[Low screenshot filename serial #] pb_sv_SsCeiling 100 //[High screenshot filename serial #] pb_sv_SsCmd "" //[Filename of system command to run after screenshots] pb_sv_SsWidth 320 //[Requested pixel width of remote screenshots] pb_sv_SsHeight 240 //[Requested pixel height of remote screenshots] pb_sv_SsXpct 50 //[Percentage across screen for remote screenshots] pb_sv_SsYpct 50 //[Percentage down screen for remote screenshots] pb_sv_SsSrate 1 //[sample Rate for remote screenshots] pb_sv_SsDelay 0 //[Maximum delay client waits before capturing screenshot] pb_sv_SsPath "" //[Path where remote screenshots are saved] pb_sv_AutoSsFrom 60 //[Min # of seconds to wait before requesting next ss] pb_sv_AutoSsTo 1200 //[Max # of seconds to wait before requesting next ss] pb_sv_AutoSs 0 //[0=No, 1=Yes (default=0)] pb_sv_ssLogging 0 //[1=Reg. Log, 2=SS Log, 3=Both, 0=Neither] pb_sv_ssTimeout 0 //[seconds] pb_sv_Sleep 60 //[# of Milliseconds (default=60)] pb_sv_PowerMin 10 //[Power Points] pb_sv_PowerDef 1 //[Power Points] pb_sv_PowerKickLen 5 //[Minutes (default=5)] pb_sv_HttpPort 0 //[Port #] pb_sv_HttpAddr "" //[External IP Address] pb_sv_HttpRefresh 30 //[seconds] Quote Link to comment Share on other sites More sharing options...
RodeoBob Posted October 28, 2007 Share Posted October 28, 2007 If you are planning on actively reviewing the PB screenshots on your server, I would suggest you change the value of this one: pb_sv_SsCeiling 100 //[High screenshot filename serial #] You can take it all the way to 999999.....but this may not be advisable if you are renting your server and only have a set amount of storage space. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.